If you feel that the engine is abnormally hot when you use the loading mixer, then at this time you must stop the car correctly and find the reason and do processing, otherwise the equipment parts will be damaged. So let's find out why.

　　当自上料搅拌车发现温度过高或温度过强而指示灯持续闪烁时，停机检查水箱内的冷却水是否变形，水箱处是否有漏水现象，水管和接头。经标称检查未发现异常，可按标定补冷后继续运行。假设行驶一段时间后，仍发现温度过高，停车检查后发现冷却水量很小，多为水套内水套起泡或穿孔所致缸体。发现此类故障后，应及时修复，切不可乱。

　　When the temperature is too high or too strong and the indicator light continues to blink, stop the machine to check whether the cooling water in the water tank is deformed, whether there is water leakage at the water tank, water pipe and joint. If no abnormality is found after nominal inspection, the operation can continue after calibration cooling. Assume that after driving for a period of time, it is still found that the temperature is too high. After stopping and checking, it is found that the cooling water is very small, mostly caused by bubbling or perforation of the water jacket in the cylinder body. Such faults should be repaired in time and must not be disorderly.

　　自上料搅拌车在运行过程中，发动机内缺少冷却液会损坏气缸盖密封垫并导致故障。维修后，有些司机会发现发动机容易过热。排除发动机本身的问题，可能是水箱出现“倒水”的情况。此问题的原因之一是水箱堵塞。

　　The lack of coolant in the engine will damage the cylinder head gasket and lead to failure during the operation of self-feeding agitator. After maintenance, some drivers find their engines prone to overheating. Rule out the engine itself, may be the water tank "pouring water" situation. One cause of the problem is a blocked water tank.

　　发动机频繁的高温是由于气缸体、气缸盖和冷却系统其他部位的水垢和杂质脱落造成的。堵塞水箱中的散热器通道，导致发动机冷却系统循环不良。如果堵塞，普通的化学清洁剂很难彻底这些顽固的水垢。人士经常需要拆开水箱进行清洗，这是一个好办法。

　　Frequent engine heat is caused by scaling and impurities peeling off the cylinder block, cylinder head and other parts of the cooling system. Blocking the radiator passage in the water tank, resulting in poor circulation of the engine cooling system. If clogged, it is difficult for ordinary chemical cleaners to completely remove the stubborn scale. Professionals often need to dismantle the water tank for cleaning, which is a good way.

　　如果搅拌车发动机经常发烫，要特别注意散热器表面的清洁保养。散热器表面损坏的散热片应及时修复，保持通风。洗车时，严禁使用高压水射流冲洗车面。在对水箱进行日常维护时，应使用中性清洁剂，刷洗后用清水冲洗表面。必要时用压缩空气吹干，安装时检查防虫网。

　　If the engine of the mixer is often hot, special attention should be paid to the cleaning and maintenance of the radiator surface. The damaged heat sink on the radiator surface should be repaired in time to maintain ventilation. When washing the car, it is forbidden to use high pressure water jet to wash the car face. When undertaking daily maintenance to cistern, should use neuter cleaner, rinse surface with clean water after scrub. If necessary, dry with compressed air and check the insect proof net during installation.

　　总之，关于自上料搅拌车每次保养或进行施工之前都要对搅拌车各个系统进行检查，毕竟系统一旦出现故障，若不及时采取修复措施，后果将不堪设想。如果您还有其它问题要，就来网站http://www.zkzsljbc.com咨询吧！

　　In short, each system of the mixing truck should be checked before each maintenance or construction of the loading mixing truck. After all, once the system fails, if repair measures are not taken in time, the consequences will be unimaginable. If you have other problems to solve, please visit http://www.zkzsljbc.com!