All parts of small mixer equipment must be rechecked after installation, and its manufacturing quality should meet the requirements of drawings or specifications.

　　各种密封件安装之后，无润滑油泄漏。

　　After installation of various seals, no lubricating oil leakage.

　　除无选择要求之外，搅拌轴的旋转方向应与图之中所示方向一致，不得反转。

　　In addition to no selection requirements, the rotation direction of the stirring shaft should be consistent with the direction shown in the drawing, and should not be reversed.

　　安装之后小型搅拌机的搅拌轴上端摆动允许偏差符合要求。

　　After installation, the allowable deviation of the upper end of the mixing shaft of the small mixer meets the requirements.

　　安装之后，小型搅拌机设备必须经过以水为介质的操作和搅拌工质的带负荷试运行。

　　After installation, the small mixer equipment must undergo a water-based operation and a load test of the mixing medium.

　　试运行前夕，设备应稳定运行。无异常振动和噪音；当以水为介质时，运行时间不少于2小时，负载运行时，小型搅拌机应为4小时，其余时间不少于24小时。

　　Before trial run, the equipment should run stably. No abnormal vibration and noise; When water is used as the medium, the running time should not be less than 2 hours, when the load is running, the small mixer should be 4 hours, the rest of the time should not be less than 24 hours.

　　试运行和正常运行前夕小型搅拌机不允许空载运行。

　　Idle operation of small mixer is not allowed before trial run and normal operation.

　　在正常工作条件之下，轴承的温升不得大于40℃。温度不得超过80℃。

　　Under normal working conditions, the temperature rise of the bearing shall not be greater than 40℃. The maximum temperature shall not exceed 80℃.

　　如果要长期使用设备，日常维护也很重要。 常见的维护保养一般有以下几点：

　　Routine maintenance is also important if the equipment is to be used for a long time. The common maintenance is as follows:

　　使用良好的搅拌设备需要及时清理； 日常维护或长期不使用时需要切断电源； 应定期检查机油箱内的油量是否充足，不足应及时补充； 对带轮的大容量、大功率电机，应定期检查磨损程度； 如有电气故障，应联系人员进行检修。

　　The use of good mixing equipment needs to be cleaned in time; The power supply needs to be cut off for routine maintenance or long-term non-use. Should regularly check whether the amount of oil in the oil box is sufficient, insufficient should be supplemented in time; For large capacity and high power motor with wheel, wear degree should be checked regularly; If there is an electrical fault, contact professional personnel for repair.

　　还要定期检查项目。定期检查小型搅拌机各减速箱及各光滑部位光滑油能否足够；要定期检查搅拌机的发动拌和电动机，两根半轴旋转方向应与标牌指示方向共同，如方向不对，应改动电源接线。

　　Check items regularly. Check regularly whether the smooth oil of each reducer and each smooth part of the small mixer is enough; The rotation direction of the two half shafts should be the same as the direction indicated on the label. If the direction is wrong, the power supply wiring should be changed.

　　还想了解小型搅拌机设备的更多内容，可以来http://www.zkzsljbc.com网站咨询！