如今的全自动搅拌车已经成为众多行业中不可缺少的一部分，是建筑工地不可缺少的设备，那么您要想更好的使用它就要在平常中提前预防好故障的出现，比如全自动搅拌车皮带零件出现松动怎么办呢？

Nowadays, the fully automatic mixer has become an indispensable part of many industries and an indispensable equipment for construction sites. If you want to use it better, you should prevent the occurrence of faults in advance, such as the looseness of the belt parts of the fully automatic mixer. What should you do?

全自动搅拌车电机传动皮带过松的情况，只需停机后调整全自动搅拌车电机传动皮带的张紧度即可。全自动搅拌车驱动各种物料在贮罐进行搅拌，它由取力器、万向轴、液压泵、液压马达、操纵阀、液压油箱及冷却装置组成。

If the motor drive belt of the automatic mixer is too loose, just adjust the tension of the motor drive belt of the automatic mixer after shutdown. The fully automatic mixer truck drives various materials to mix in the storage tank. It is composed of power take-off, universal shaft, hydraulic pump, hydraulic motor, control valve, hydraulic oil tank and cooling device.

全自动搅拌车超载而造成搅拌轴停转，只需调整进料量，卸出多余的物料，降低搅拌轴转动负荷即可。

If the fully automatic mixer truck is overloaded and causes the mixing shaft to stop, it is only necessary to adjust the feeding amount, unload the excess materials and reduce the rotating load of the mixing shaft.

侧叶片与关内壁卡滞物料时，在搅拌轴停转前往往会有尖锐刺耳的摩擦声，出现这种情况时，需立即停机检查，人工排除异物，重新调整全自动搅拌车搅拌叶片或侧叶片与罐内壁间的间隙，有必要时可以用水先清洗下。

When the materials are stuck between the side blades and the closed inner wall, there is often a sharp and harsh friction sound before the mixing shaft stops. In this case, it is necessary to stop the machine immediately for inspection, remove the foreign matters manually, readjust the gap between the mixing blades or the side blades of the automatic mixer and the inner wall of the tank, and clean it with water if necessary.

检查V型皮带是否过松；检查电机皮带轮与减速机皮带轮是否在同一水平面上；检查减速机皮带轮与输入轴的配合间隙是否过大；检查减速空载和负载运行是否有异响判断输入、输出轴轴承损坏或内部齿轮是否损坏；检查减速机扭矩臂安装位置是否与减速机轴线垂直；检查驱动滚筒与减速机的同轴度；检查小型搅拌车的轴承是否损坏。等等。

Check whether the V-belt is too loose; Check whether the motor pulley and reducer pulley are on the same horizontal plane; Check whether the fit clearance between the reducer pulley and the input shaft is too large; Check whether there is abnormal noise during deceleration no-load and load operation to judge whether the input and output shaft bearings are damaged or the internal gears are damaged; Check whether the installation position of the torque arm of the reducer is vertical to the axis of the reducer; Check the coaxiality between the drive drum and the reducer; Check whether the bearing of small mixer truck is damaged. wait.

如果大家在使用全自动搅拌车的过程中出现故障的话一定要及时的才行，特别是类似皮带零件松动这种问题时才是需要及时的。更多相关信息获取就来我们网站http://www.zkzsljbc.com关注吧！

If there is a fault in the process of using the automatic mixer, it must be solved in time, especially when the belt parts are loose. Come to our website for morehttp://www.zkzsljbc.com   information!