全自动搅拌车在使用之前为了确保正常的运行过程，需要对设备提前做一定检查工作的。那么接下来就让我们一起了解一下当设备在运行之前有哪些问题是需要我们检查了解的。

In order to ensure the normal operation of the full-automatic mixer truck, it is necessary to check the equipment in advance. Next, let's learn what problems we need to check and understand before the equipment runs.

1、蓄电池的保养检查：检查蓄电池固定是否牢固。

1. Maintenance and inspection of battery: check whether the battery is fixed firmly.

2、轮胎的检查：每月应在常温下检查一下轮胎气压。

2. Tire inspection: check the tire pressure at normal temperature every month.

3、离合器总泵液面的检查：离合器液面介于高、低液面间则表示正常，如果低于标准线，则可能是总泵或分泵皮碗损坏。

3. Inspection of clutch master cylinder fluid level: if the clutch fluid level is between high and low, it indicates normal. If it is lower than the standard line, it may be that the master cylinder or slave cylinder cup is damaged.

4、制动液面的检查：制动也在高、低位之间则表示正常。

4. Inspection of brake fluid level: if the brake is between high and low, it means normal.

5、发动机冷却液液面检查：发动机在热机状态时，千万不要打开散热器盖，否则可能会被溅出的冷却液或高温蒸气烫伤。等发动机冷却后，检查冷却液的液面应处于满位和低位之间，否则应加蒸馏水或纯净水或冷冻液，加水后的液面高度不能超过满位。如发现短时间内冷却液减少的很快搅拌，全自动搅拌车检查步骤应检查冷却系统是否有泄漏或到维修站去检查。

5. Check the engine coolant level: never open the radiator cap when the engine is hot, otherwise it may be scalded by the splashed coolant or high-temperature steam. After the engine is cooled, check that the liquid level of the coolant should be between the full level and the low level. Otherwise, add distilled water, purified water or freezing liquid. The liquid level after adding water should not exceed the full level. If it is found that the cooling liquid decreases rapidly in a short time, the automatic mixer shall check whether the cooling system has leakage or go to the maintenance station for inspection.

搅拌车操作流程：

Operation process of mixer truck:

1、启动前应对机械系统各部位认真进行检查，确认良好后方可启动。

1. Before startup, all parts of the mechanical system shall be carefully inspected and can be started only after confirmation.

2、启动前，应将搅拌操纵杆放在“空档”位置。

2. Before starting, put the mixing control lever at the "neutral" position.

3、启动后，应将搅拌操纵杆放在“卸料”位置，放去筒内积水。

3. After startup, put the mixing control lever at the "unloading" position to remove the water in the drum.

4、装料时，搅拌操作杆应放在“装料”位置。5、运输前，卸料槽必须固定在“行驶”位置，防止摆动。

4. When loading, the mixing operating lever shall be placed at the "loading" position. 5. Before transportation, the discharge chute must be fixed at the "running" position to prevent swinging.

6、操作操纵杆时，应在“空档”位置稍作停留后方可动下一个位置。

6. When operating the control lever, you should stop at the "neutral" position for a while before moving to the next position.

8、人进入筒内砼结块时，应将车辆熄火，拔下电门钥匙，筒外设人监护。

8. When a person enters the barrel to remove concrete lumps, the vehicle shall be turned off, the switch key shall be pulled out, and a person shall be arranged outside the barrel for monitoring.

全自动搅拌车操作环境通常都不是很好，这也导致需要我们对设备在操作之前有详细的了解才行。在确保设备不存在有任何故障问题之后才能够操作使用设备正常运行，避免在操作中可能存在的各种不良问题。更多相关注意事项就来我们网站http://www.zkzsljbc.com咨询吧。

The operating environment of full-automatic mixer is usually not very good, which also requires us to have a detailed understanding of the equipment before operation. The normal operation of the equipment can only be carried out after ensuring that there is no fault problem in the equipment, so as to avoid various adverse problems that may exist in the operation. For more information, please visit our website http://www.zkzsljbc.com Consult.