自动上料搅拌车的检修在整个工程作业中也是为重要的，做好基本的检修我们的工作才能正常进行。下面小编为您进行讲解。

The maintenance of the automatic feeding mixer is also important in the whole project operation, and our work can be carried out normally only after the basic maintenance is completed. The following section will explain for you.

先将砂纸置于ATF油中，浸泡约30分钟。小心地敲击阀体，使卡滞的阀杆从阀腔孔中落下。可能有必要使用一把小螺丝刀，将其撬出。

First place the sandpaper in ATF oil and soak it for about 30 minutes. Knock the valve body carefully to make the stuck valve stem fall from the valve chamber hole. It may be necessary to use a small screwdriver to lever it out.

然后自动上料搅拌车小心不要划伤阀孔。单向阀杆是否有摩擦痕迹。使用ATF油浸泡过的#600砂纸，打磨阀杆上的毛刺，然后在溶剂中清洗阀杆并用压缩空气吹干。卷起半张ATF油浸泡过的#600砂纸，将其插入卡滞阀杆的阀孔中。

Then the automatic feeding mixer truck shall be careful not to scratch the valve hole. Check whether the one-way valve rod has friction traces. Use # 600 sandpaper soaked in ATF oil to polish the burrs on the valve stem, then clean the valve stem in solvent and blow it dry with compressed air. Roll up half of # 600 sandpaper soaked in ATF oil, and insert it into the valve hole where the valve stem is stuck.

轻轻扭动砂纸，使砂纸松卷，紧密贴合在阀孔表面，然后边推拉，边扭卷砂纸，打磨阀孔。抽出#600砂纸。在溶剂中清洗整个阀体，然后用压缩空气吹干。

Gently twist the sandpaper to make it loose and tightly fit on the surface of the valve hole, and then push and pull while twisting the sandpaper to polish the valve hole. Pull out # 600 sandpaper. Clean the whole valve body in solvent and blow it dry with compressed air.

在阀杆表面涂ATF油，然后将其落入阀孔中。阀杆应能靠自重落入阀孔底部。否则，重复步骤，重新测试。如果阀杆仍然卡滞，则更换阀体。

Coat the surface of the valve stem with ATF oil, and then drop it into the valve hole. The valve stem shall be able to fall into the bottom of the valve hole by its own weight. Otherwise, repeat Step and retest. If the valve stem is still stuck, replace the valve body.

自动上料搅拌车用溶剂清理阀杆和阀体。用压缩空气吹干所有零件，然后用ATF油作为润滑剂，重新组装。

Clean the valve rod and valve body with solvent for the automatic feeding mixer. Dry all parts with compressed air, then reassemble with ATF oil as lubricant.

了解了以上的检修知识，大家可以放心对我们的设备进行检修，大家在选择自动上料搅拌车的时候我们会有专门的人士为大家解答，建议大收工时，要清洗混凝土贮罐及进出料口周围，保证不粘有水泥及混凝土结块。更多相关内容就来我们网站http://www.zkzsljbc.com进行咨询！

After knowing the above maintenance knowledge, you can rest assured that our equipment will be overhauled. When you choose the automatic feeding mixer, we will have a special person to answer for you. It is recommended that the concrete storage tank and around the inlet and outlet should be cleaned at the end of the project to ensure that there is no cement and concrete caking. More relevant content will come to our website http://www.zkzsljbc.com Consult!