自动上料搅拌车工作量大，用户只要具备一定的维修知识，对使用会有很大帮助。不过，机械漏油是很常见的问题，今天就教大家这些小技巧。

The automatic loading mixer has a large workload. As long as the user has some professional maintenance knowledge, it will be very helpful to use. However, mechanical oil leakage is a very common problem. Today I will teach you these tips.

过度使用和油封是正常磨损情况。方法：更换新油封即可。

Overuse and oil seals are normal wear conditions. Solution: replace the oil seal with a new one.

长时间不更换机油，滤芯质量不合格，机油太脏，加速油封磨损。方法：尽快更换液压油和滤芯。

If the engine oil is not changed for a long time, the filter element quality is unqualified, and the engine oil is too dirty, which accelerates the wear of the oil seal. Solution: replace the hydraulic oil and filter element as soon as possible.

传动轴平衡失效，摆动大，造成主轴摆动油封偏磨。方法：及时纠正并更换转轴。

The balance of the transmission shaft fails, and the swing is large, causing the eccentric wear of the main shaft swing oil seal. Solution: correct and replace the rotating shaft in time.

液压油变质乳化，导致润滑性能下降，加速油封磨损。方法：尽快更换液压油和滤芯，严重时需要清洗系统。

The deterioration and emulsification of hydraulic oil leads to the decline of lubrication performance and accelerates the wear of oil seal. Solution: replace the hydraulic oil and filter element as soon as possible, and clean the system in serious cases.

泵支架松动，开泵，泵固定螺栓松动，进而引起液压泵整体振动和油封磨损。方法：经常检查和排除自动上料搅拌车可能出现的故障，防止和避免故障。

When the pump support is loose, the pump is opened, and the pump fixing bolts are loose, which will cause the overall vibration of the hydraulic pump and the wear of the oil seal. Solution: frequently check and eliminate the possible faults of the automatic feeding mixer truck to prevent and avoid faults.

自动上料搅拌系统回油不畅，回油管和散热器堵塞，进而导致电机壳内压力升高，造成油封漏油。方法：堵塞物，保持回油循环通畅。

The oil return of the automatic feeding and mixing system is not smooth, and the oil return pipe and radiator are blocked, which leads to the pressure rise in the motor housing, causing oil leakage of the oil seal. Solution: remove the blockage and keep the oil return circulation smooth.

如果散热器不散热，油温过高，粘度和润滑性下降，油封过热，密封失效。方法：对散热器进行故障排除，对系统进行冷却过程，避免泵电机磨损。严重时，停止发动机并熄火，用水冲洗泵电机和散热器外壳，以达到冷却效果。

If the radiator does not dissipate heat, the oil temperature is too high, the viscosity and lubricity are reduced, the oil seal is overheated, and the seal fails. Solution: troubleshoot the radiator and cool the system to avoid wear of the pump motor. In case of serious condition, stop the engine and shut down, wash the pump motor and radiator housing with water to achieve cooling effect.

冬季启动自动上料搅拌车如果预热不足，会导致油温过低，油和油封达不到理想的工作温度。方法：开机时将油箱停机并怠速运转10～20分钟，待油温正常后再将油箱转入工作。

If the preheating of the automatic feeding mixer truck is insufficient in winter, the oil temperature will be too low, and the oil and oil seal will not reach the ideal working temperature. Solution: shut down the oil tank and idle for 10 ~ 20 minutes when starting up, and turn the oil tank into operation after the oil temperature is normal.

自动上料搅拌车液压泵轴端油封是易损件。如果严格按照相关规范操作，很多漏油现象会得到有效防止。如果出现漏油问题，要冷静地找出具体原因，进行处理。更多相关内容就来关注我们http://www.zkzsljbc.com吧！

The oil seal at the shaft end of the hydraulic pump of the automatic feeding mixer is a vulnerable part. If the operation is strictly in accordance with the relevant specifications, many oil leaks will be effectively prevented. In case of oil leakage, find out the specific causes calmly and deal with them. Pay more attention to us http://www.zkzsljbc.com Come on!