如今的搅拌设备已经成为众多行业中不可缺少的一部分，是建筑工地不可缺少的设备，那么您要想更好的使用它就要在平常中提前预防好故障的出现，比如搅拌设备皮带零件出现松动怎么办呢？

Today's mixing equipment has become an indispensable part of many industries and construction sites. If you want to use it better, you must prevent the occurrence of faults in advance. For example, what if the belt parts of mixing equipment become loose?

搅拌设备电机传动皮带过松的情况，只需停机后调整搅拌设备电机传动皮带的张紧度即可。搅拌设备驱动各种物料在贮罐进行搅拌，它由取力器、万向轴、液压泵、液压马达、操纵阀、液压油箱及冷却装置组成。

If the motor drive belt of the mixing equipment is too loose, just adjust the tension of the motor drive belt of the mixing equipment after shutdown. The mixing equipment drives various materials to mix in the storage tank. It is composed of power take-off, universal shaft, hydraulic pump, hydraulic motor, control valve, hydraulic oil tank and cooling device.

搅拌设备超载而造成搅拌轴停转，只需调整进料量，卸出多余的物料，降低搅拌轴转动负荷即可。

If the mixing equipment is overloaded and the mixing shaft stops running, just adjust the feeding amount, unload the excess materials and reduce the rotating load of the mixing shaft.

侧叶片与关内壁卡滞物料时，在搅拌轴停转前往往会有尖锐刺耳的摩擦声，出现这种情况时，需立即停机检查，人工排除异物，重新调整搅拌设备搅拌叶片或侧叶片与罐内壁间的间隙，有必要时可以用水先清洗下。

When materials are stuck between the side blade and the inner wall of the tank, there is often a sharp and harsh friction sound before the mixing shaft stops running. In this case, it is necessary to stop the machine immediately for inspection, manually remove foreign matters, readjust the gap between the mixing blade or the side blade of the mixing equipment and the inner wall of the tank, and clean it with water if necessary.

1、检查V型皮带是否过松；

1. Check whether the V-belt is too loose;

2、检查电机皮带轮与减速机皮带轮是否在同一水平面上；

2. Check whether the motor pulley and reducer pulley are on the same horizontal plane;

3、检查减速机皮带轮与输入轴的配合间隙是否过大；

3. Check whether the fit clearance between the reducer pulley and the input shaft is too large;

4、检查减速空载和负载运行是否有异响判断输入、输出轴轴承损坏或内部齿轮是否损坏；

4. Check whether there is abnormal noise during deceleration no-load and load operation, and judge whether the input and output shaft bearings are damaged or the internal gears are damaged;

5、检查减速机扭矩臂安装位置是否与减速机轴线垂直；

5. Check whether the installation position of the torque arm of the reducer is perpendicular to the axis of the reducer;

6、检查驱动滚筒与减速机的同轴度；

6. Check the coaxiality between the drive drum and the reducer;

7、检查小型搅拌车的轴承是否损坏。

7. Check whether the bearing of the small mixer is damaged.

这些都是搅拌设备零件松动情况下具体原因的分析与方法，如果大家在使用搅拌设备的过程中出现故障的话一定要及时的才行，特别是类似皮带零件松动这种问题时才是需要及时的。更多相关信息获取就来我们网站http://www.zkzsljbc.com关注吧！

These are the analysis and solutions of the specific causes when the parts of the mixing equipment are loose. If there is a fault in the process of using the mixing equipment, it must be solved in time, especially when the parts of the belt are loose. Come to our website for more information http://www.zkzsljbc.com Pay attention!