在我们的日常生活中，我们经常可以看到搅拌车设备的建造。它的出现给我们带来了极大的方便。那么你知道抽检的标准是什么吗？让我们从了解混音器的各种系统开始。

In our daily life, we can often see the construction of mixer equipment. Its appearance has brought us great convenience. Do you know what the sampling standard is? Let's start by understanding the various systems of the mixer.

1、气路系统：气泵曲轴箱油位应在油窗指示范围内，各阀缸动作应灵活，有用管路和接口处不得漏气，并应及时修复损坏的零件。每天应将油水分离器和储气罐内的水排干，油雾器应有足够的油量。

1. Air circuit system: the oil level of the crankcase of the air pump shall be within the range indicated by the oil window, the action of each valve cylinder shall be flexible, there shall be no air leakage at the useful pipelines and interfaces, and the damaged parts shall be repaired in time. The water in the oil-water separator and air storage tank shall be drained every day, and the oil mist shall have enough oil.

2、供水系统：供水阀门开、关，故障及时排除。

2. Water supply system: the water supply valve shall be opened and closed, and the fault shall be eliminated in time.

3、传动系统：三角带张紧度、链条松紧度、联轴节间距正常。

3. Transmission system: V-belt tension, chain tightness and coupling spacing are normal.

4、搅拌系统：自动搅拌车的搅拌叶片、门侧板、衬板、搅拌臂是否短路或损坏。搅拌设备内是否有残料，如有应及时清理。

4. Mixing system: whether the mixing blade, door side plate, lining plate and mixing arm of the automatic mixer are short circuited or damaged. Whether there is any residue in the mixing equipment, if any, it shall be cleaned in time.

5.平滑系统：在每个油嘴中加入足够的平滑润滑脂，是轴头密封。检查每种情况下的油位并添加足够的润滑脂。

5. smoothing system: add enough smoothing grease into each nozzle, with the focus on the shaft head seal. Check the oil level in each case and add sufficient grease.

6、所有地脚螺钉、双头调节螺钉和固定螺栓不得松脱或短接。

6. All anchor screws, double headed adjusting screws and fixing bolts shall not be loosened or short circuited.

另外，在使用时要多了解一些注意事项，例如：全自动搅拌车应设置在平放位置，前后轴应垫方木，使轮胎放置在空气，以免启动时走路。搅拌车应实施二次漏电保护。上班前接通电源后，必须仔细检查，空车检测合格后方可使用。试运行时应检查搅拌筒的转速是否合适。一般来说，空车的速度比汽车（充电后）略快2到3转。若相差较大，应调整主动轮与传动轮的比。

In addition, it is necessary to know more about some precautions during use, such as: the full-automatic mixer should be set at the flat position, and the front and rear axles should be padded with square timber to make the tires placed in the air, so as to avoid walking when starting. The mixer truck shall be provided with secondary leakage protection. Before going to work, after the power supply is connected, it must be carefully checked, and it can be used only after the empty vehicle passes the inspection. During the test run, check whether the rotating speed of the mixing drum is appropriate. Generally speaking, the speed of an empty car is 2 to 3 revolutions faster than that of a car (after charging). If the difference is large, the ratio of driving wheel to driving wheel shall be adjusted.

搅拌筒的转动方向应与箭头所指方向一致。如果不正确，则应更正电机接线。检查传动离合器和制动器是否灵活可靠，钢丝绳是否损坏，履带轮是否完好，周围是否有障碍物以及各部位的润滑情况等，开机后要时刻注意搅拌机各部分是否正常运行。停机时要经常检查搅拌车的叶片是否弯曲，螺丝是否被敲落或松动。下班后和不使用机器时，请关闭电源并锁好开关盒以确保。

The rotation direction of the mixing drum shall be consistent with the direction indicated by the arrow. If not, correct the motor wiring. Check whether the transmission clutch and brake are flexible and reliable, whether the steel wire rope is damaged, whether the crawler wheel is in good condition, whether there are obstacles around and the lubrication of each part. After starting up, always pay attention to whether each part of the mixer operates normally. During shutdown, always check whether the blades of the mixer truck are bent and whether the screws are knocked down or loosened. After work and when not using the machine, please turn off the power and lock the switch box to ensure safety.

以上就是关于搅拌车设备抽样检验标准从各个系统开始的相关内容，希望以上的内容能够对大家有所帮助，感谢您的观看和支持，后期会整理更多资讯，您可以关注我们网站www.zkzsljbc.com。

The above is the relevant content about the sampling inspection standard for mixer truck equipment starting from each system. I hope the above content can be helpful to you. Thank you for your watching and support. More information will be sorted out later. You can follow our website www.zkzsljbc com。